Minggu, 19 Juli 2009

Termodinamika

Disusun Ulang Oleh:

Arip Nurahman

Pendidikan Fisika, FPMIPA. Universitas Pendidikan Indonesia

&

Follower Open Course Ware at MIT-Harvard University. Cambridge. USA.


Materi kuliah termodinamika ini disusun dari hasil perkuliahan di departemen fisika FPMIPA Universitas Pendidikan Indonesia dengan Dosen:

1. Bpk. Drs. Saeful Karim, M.Si.

2. Bpk. Insan Arif Hidayat, S.Pd., M.Si.

Dan dengan sumber bahan bacaan lebih lanjut dari :

Massachusetts Institute of Technology, Thermodynamics

Professor Z. S. Spakovszk, Ph.D.

Office: 31-265

Phone: 617-253-2196

Email: zolti@mit.edu

Aero-Astro Web: http://mit.edu/aeroastro/people/spakovszky

Gas Turbine Laboratory: home

2.1 First Law of Thermodynamics

[VW, S & B: 2.6]

Observation leads to the following two assertions:

  1. There exists for every system a property called energy, $ E$ . The system energy can be considered as a sum of internal energy, kinetic energy, potential energy, and chemical energy.
    1. Like the Zeroth Law, which defined a useful property, ``temperature,'' the First Law defines a useful property called ``energy.''
    2. The two new terms (compared to what you have seen in physics and dynamics, for example) are the internal energy and the chemical energy. For most situations in this class, we will neglect the chemical energy. We will generally not, however, neglect the internal energy, $ u$ . It arises from the random or disorganized motion of molecules in the system, as shown in Figure 2.1. Since this molecular motion is primarily a function of temperature, the internal energy is sometimes called ``thermal energy.''

      Figure 2.1: Random motion is the physical basis for internal energy
      Image fig3RandomMotion_web

      The internal energy, $ u$ , is a function of the state of the system. Thus $ u = u (p, T)$ , or $ u = u (p, v)$ , or $ u = u(v,T)$ . Recall that for pure substances the entire state of the system is specified if any two properties are specified. (We will discuss the equations that relate the internal energy to these other variables as the course progresses.)

  2. The change in energy of a system is equal to the difference between the heat added to the system and the work done by the system,
    $\displaystyle \Delta E = Q - W \qquad \textrm{(units are Joules, J)},$ (2..1)

    where $ E$ is the energy of the system,
    $ Q$ is the heat input to the system, and
    $ W$ is the work done by the system.
    $ E = U$ (thermal energy) + $ E_{kinetic} + E_{potential} + \dots$
    1. Like the Zeroth Law, the First Law describes the behavior of the new property [VW, S& B: Chapter 5].
    2. The equation can also be written on a per unit mass basis
      $\displaystyle \Delta e = q - w \qquad \textrm{(units are J/kg)}.$

    3. In many situations the potential energy, kinetic energy, and chemical energy of the system are constant or not important. Then
      $\displaystyle \Delta E = \Delta U,$

      and
      $\displaystyle \Delta U = Q - W \qquad \textrm{or} \qquad \Delta u = q - w.$

    4. Note that $ Q$ and $ W$ are not functions of state, but $ U$ , which arises from molecular motion (see above), depends only on the state of the system; $ U$ does not depend on how the system got to that state. We therefore have the striking result that:
      $\displaystyle \textbf{$\Delta U$ is independent of path even though $Q$ and $W$ are not!}$

      Sometimes this difference is emphasized by writing the First Law in differential form,

      $\displaystyle d U = \delta Q - \delta W \qquad \textrm{or} \qquad du = \delta q - \delta w,$ (2..2)

      where the symbol ``$ \delta$ '' is used to denote that these are not exact differentials but rather are dependent on path.
    5. Note that the signs are important:
      • $ Q$ is defined to be positive if it is transferred to the system; thus the numerical value we substitute for $ Q$ will be positive if heat is transferred to the system from the surroundings, and negative if heat is transferred from the system to the surroundings. [VW, S & B: 4.7-4.8]
      • $ W$ is defined to be positive if it is done by the system (see Section 1.3); thus the numerical value we substitute for $ W$ will be positive if the system is doing work, and negative if work is being done on the system. [VW, S& B: 4.1-4.4]
    6. For quasi-static processes we can substitute $ W = p_{\textrm{sys}} dV$ ,
      $\displaystyle dU = \delta Q - pdV \qquad \textrm{or} \qquad du = \delta q - pdv$

To give an example of where the first law is applied, consider the device shown in Figure 2.2. We heat a gas, it expands against a weight, some force (pressure times area) is applied over a distance, and work is done. The change in energy of the system supplies the connection between the heat added and work done. We will spend most of the course dealing with various applications of the first law -- in one form or another.

Figure 2.2: The change in energy of a system relates the heat added to the work done
Image fig3RaiseAWeight_web

The form of the first law we have given here is sometimes called the ``control mass'' form, because it is well suited to dealing with systems of a fixed mass. We will see in Section 2.5 that this form can be written for a control volume with mass flow in and mass flow out (like a jet engine for example). We will call this the ``control volume'' form of the first law [VW, S & B: 5.8-5.12].





Muddy Points

What are the conventions for work and heat in the first law? (MP 2.1)

When does $ E\rightarrow U$ ? (MP 2.2)


Ucapan Terima Kasih:

Kepada Para Dosen di MIT dan Dosen Fisika FPMIPA Universitas Pendidikan Indonesia

Semoga Bermanfaat

Sabtu, 18 Juli 2009

Termodinamika

Disusun Ulang Oleh:

Arip Nurahman

Pendidikan Fisika, FPMIPA. Universitas Pendidikan Indonesia

&

Follower Open Course Ware at MIT-Harvard University. Cambridge. USA.


Materi kuliah termodinamika ini disusun dari hasil perkuliahan di departemen fisika FPMIPA Universitas Pendidikan Indonesia dengan Dosen:

1. Bpk. Drs. Saeful Karim, M.Si.

2. Bpk. Insan Arif Hidayat, S.Pd., M.Si.

Dan dengan sumber bahan bacaan lebih lanjut dari :

Massachusetts Institute of Technology, Thermodynamics

Professor Z. S. Spakovszk, Ph.D.

Office: 31-265

Phone: 617-253-2196

Email: zolti@mit.edu

Aero-Astro Web: http://mit.edu/aeroastro/people/spakovszky

Gas Turbine Laboratory: home






2.4 Specific Heats: the relation between temperature change and heat

[VW, S& B: 5.6]

How much does a given amount of heat transfer change the temperature of a substance? It depends on the substance. In general

$\displaystyle Q = C\Delta T,$ (2..4)

where $ C$ is a constant that depends on the substance. We can determine the constant for any substance if we know how much heat is transferred. Since heat is path dependent, however, we must specify the process, i.e., the path, to find $ C$ .

Two useful processes are constant pressure and constant volume, so we will consider these each in turn. We will call the specific heat at constant pressure $ C_p$ , and that at constant volume $ C_v$ , or $ c_p$ and $ c_v$ per unit mass.

  1. The Specific Heat at Constant Volume

    Remember that if we specify any two properties of the system, then the state of the system is fully specified. In other words we can write $ u = u(T,v)$ , $ u = u (p, v)$ or $ u = u (p, T)$ . [VW, S & B: 5.7]

    Consider the form $ u = u(T,v)$ , and use the chain rule to write how $ u$ changes with respect to $ T$ and $ v$ :

    $\displaystyle du = \left(\frac{\partial u}{\partial T}\right)_v dT + \left(\frac{\partial u}{\partial v}\right)_T dv.$ (2..5)

    For a constant volume process, the second term is zero since there is no change in volume, $ dv = 0$ . Now if we write the First Law for a quasi-static process, with $ dW = pdv$ ,
    $\displaystyle du = \delta q - pdv,$ (2..6)

    we see that again the second term is zero if the process is also constant volume. Equating (2.5) and (2.6) with $ dv$ canceled in each,
    $\displaystyle \delta q = \left(\frac{\partial u}{\partial T}\right)_v dT,$

    and rearranging


    $\displaystyle \left(\frac{\partial u}{\partial T}\right)_v = \left(\frac{\partial q}{\partial T}\right)_v.$

    In this case, any energy increase is due only to energy transfer as heat. We can therefore use our definition of specific heat from Equation (2.4) to define the specific heat for a constant volume process,
    $\displaystyle c_v \equiv \left(\frac{\partial u}{\partial T}\right)_v.$

  2. The Specific Heat at Constant Pressure

    If we write $ h=h(T,p)$ , and consider a constant pressure process, we can perform a similar derivation to the one above and show that

    $\displaystyle c_p \equiv \left(\frac{\partial h}{\partial T}\right)_p.$

In the derivation of $ c_v$ , we considered only a constant volume process, hence the name, ``specific heat at constant volume.'' It is more useful, however, to think of $ c_v$ in terms of its definition as a certain partial derivative, which is a thermodynamic property, rather than as a quantity related to heat transfer in a special process. In fact, the derivatives above are defined at any point in any quasi-static process whether that process is constant volume, constant pressure, or neither. The names ``specific heat at constant volume'' and ``specific heat at constant pressure'' are therefore unfortunate misnomers; $ c_v$ and $ c_p$ are thermodynamic properties of a substance, and by definition depend only the state. They are extremely important values, and have been experimentally determined as a function of the thermodynamic state for an enormous number of simple compressible substances2.1.

To recap:

$\displaystyle c_p=\left(\frac{\partial h}{\partial T}\right)_p\quad \textrm{ and }\quad c_v = \left(\frac{\partial u}{\partial T}\right)_v.$

or

$\displaystyle C_p=\left(\frac{\partial H}{\partial T}\right)_p\quad \textrm{ and }\quad C_v = \left(\frac{\partial U}{\partial T}\right)_v.$





Practice Questions Throw an object from the top tier of the lecture hall to the front of the room. Estimate how much the temperature of the room has changed as a result. Start by listing what information you need to solve this problem.

2.4.1 Specific Heats of an Ideal Gas

The equation of state for an ideal gas is

$\displaystyle PV = N\mathcal{R} T,$

where $ N$ is the number of moles of gas in the volume $ V$ . Ideal gas behavior furnishes an extremely good approximation to the behavior of real gases for a wide variety of aerospace applications. It should be remembered, however, that describing a substance as an ideal gas constitutes a model of the actual physical situation, and the limits of model validity must always be kept in mind.

One of the other important features of an ideal gas is that its internal energy depends only upon its temperature. (For now, this can be regarded as another aspect of the model of actual systems that the ideal gas represents, but it can be shown that this is a consequence of the form of the equation of state.) Since $ u$ depends only on $ T$ ,

$\displaystyle du$ $\displaystyle = \left(\frac{\partial u}{\partial T}\right)_v dT + \cancelto{0}{\left(\frac{\partial u}{\partial v}\right)_T} dv$

or


$\displaystyle du$ $\displaystyle = c_v(T) dT.$

In the above equation we have indicated that $ c_v$ can depend on $ T$ . Like the internal energy, the enthalpy is also only dependent on $ T$ for an ideal gas. (If $ u$ is a function of $ T$ , then, using the ideal gas equation of state, $ u+Pv$ is also.) Therefore,
$\displaystyle dh$ $\displaystyle = \left(\frac{\partial h}{\partial T}\right)_p dT + \cancelto{0}{\left(\frac{\partial h}{\partial p}\right)_T} dp,$

and


$\displaystyle dh$ $\displaystyle = c_p(T) dT.$

If we are interested in finite changes of internal energy or enthalpy, we integrate,
$\displaystyle \Delta u_{\textrm{1-2}} = \int_{T_1}^{T_2} c_v(T)dT$

and
$\displaystyle \Delta h_{1-2} = \int_{T_1}^{T_2}c_p(T)dT.$

Over small temperature changes ( $ \Delta T \approx 200\textrm{ K}$ ), it is often assumed that $ c_v$ and $ c_p$ are constant. Furthermore, there are wide ranges over which specific heats do not vary greatly with respect to temperature, as shown in SB&VW Figure 5.11. It is thus often useful to treat them as constant. If so
$\displaystyle du$ $\displaystyle = c_v dT,$
$\displaystyle dh$ $\displaystyle = c_p dT,$
$\displaystyle u_2 - u_1$ $\displaystyle = c_v (T_2 - T_1),$
$\displaystyle h_2 - h_1$ $\displaystyle = c_p (T_2 - T_1).$

These equations are useful in calculating internal energy or enthalpy differences, but it should be remembered that they hold only if the specific heats are constant.

We can relate the specific heats of an ideal gas to its gas constant as follows. We write the first law in terms of internal energy,

$\displaystyle \delta q = du + dW,$

and assume a quasi-static process so that we can also write it in terms of enthalpy, as in Section 2.3.4,
$\displaystyle \delta q = dh - v dp.$

Equating the two first law expressions above, and assuming an ideal gas, we obtain
$\displaystyle c_p dT - vdp = c_v dT + pdv.$

Combining terms,
$\displaystyle (c_p - c_v)dT$ $\displaystyle = d(pv)$
$\displaystyle c_p - c_v$ $\displaystyle = \frac{d(pv)}{dT}.$

Since $ pv = RT$ ,
$\displaystyle c_p - c_v = R.$

An expression that will appear often is the ratio of specific heats, which we will define as
$\displaystyle \gamma = \frac{c_p}{c_v}.$

Below we summarize the important results for all ideal gases, and give some values for specific types of ideal gases.
  1. All ideal gases:
    1. The specific heat at constant volume ($ c_v$ for a unit mass or $ C_V$ for one kmol) is a function of $ T$ only.
    2. The specific heat at constant pressure ($ c_p$ for a unit mass or $ C_P$ for one kmol) is a function of $ T$ only.
    3. A relation that connects the specific heats $ c_p$ , $ c_v$ , and the gas constant is

      $\displaystyle c_p - c_v = R$

      where the units depend on the mass considered. For a unit mass of gas, e.g., a kilogram, $ c_p$ and $ c_v$ would be the specific heats for one kilogram of gas and $ R$ is as defined above. For one kmol of gas, the expression takes the form

      $\displaystyle C_P - C_V = \mathcal{R},$

      where $ C_P$ and $ C_V$ have been used to denote the specific heats for one kmol of gas and $ \mathcal{R}$ is the universal gas constant.
    4. The specific heat ratio, $ \gamma = c_p/c_v$ (or $ C_P/C_V$ ), is a function of $ T$ only and is greater than unity.
  2. An ideal gas with specific heats independent of temperature, $ c_p = \textrm{const}$ and $ c_v = \textrm{const}$ , is referred to as a perfect gas. For example, monatomic gases and diatomic gases at ordinary temperatures are considered perfect gases. To make this distinction the terminology "a perfect gas with constant specific heats" is used throughout the notes. In some textbooks perfect gases are sometimes also referred to as ideal gases, and to avoid confusion we use the stated terminology2.2.
  3. Monatomic gases, such as He, Ne, Ar, and most metallic vapors:
    1. $ c_v$ (or $ C_V$ ) is constant over a wide temperature range and is very nearly equal to $ (3/2)R$ [or $ (3/2)\mathcal{R}$ , for one kmol].
    2. $ c_p$ (or $ C_P$ ) is constant over a wide temperature range and is very nearly equal to $ (5/2)R$ [or $ (5/2)\mathcal{R}$ , for one kmol].
    3. $ \gamma$ is constant over a wide temperature range and is very nearly equal to $ 5/3$ [ $ \gamma= 1.67$ ].
  4. So-called permanent diatomic gases, namely H$ _2$ , O$ _2$ , N$ _2$ , Air, NO, and CO:
    1. $ c_v$ (or $ C_V$ ) is nearly constant at ordinary temperatures, being approximately $ (5/2)R$ [ $ (5/2)\mathcal{R}$ , for one kmol], and increases slowly at higher temperatures.
    2. $ c_p$ (or $ C_P$ ) is nearly constant at ordinary temperatures, being approximately $ (7/2)R$ [ $ (7/2)\mathcal{R}$ , for one kmol], and increases slowly at higher temperatures.
    3. $ \gamma$ is constant over a temperature range of roughly $ 150\textrm{ K}$ to $ 600\textrm{ K}$ and is very nearly equal to $ 7/5$ [ $ \gamma= 1.4$ ]. It decreases with temperature above this.
  5. Polyatomic gases and gases that are chemically active, such as CO$ _2$ , NH$ _3$ , CH$ _4$ , and Freons:

    The specific heats, $ c_v$ and $ c_p$ , and $ \gamma$ vary with the temperature, the variation being different for each gas. The general trend is that heavy molecular weight gases (i.e., more complex gas molecules than those listed in 2 or 3), have values of $ \gamma$ closer to unity than diatomic gases, which, as can be seen above, are closer to unity than monatomic gases. For example, values of $ \gamma$ below 1.2 are typical of Freons which have molecular weights of over one hundred.2.3

In general, for substances other than ideal gases, $ u$ and $ h$ depend on pressure as well as on temperature, and the above relations will not all apply. In this respect, the ideal gas is a very special model.

In summary, the specific heats are thermodynamic properties and can be used even if the processes are not constant pressure or constant volume. The simple relations between changes in energy (or enthalpy) and temperature are a consequence of the behavior of an ideal gas, specifically the dependence of the energy and enthalpy on temperature only, and are not true for more complex substances.2.4


2.4.2 Reversible adiabatic processes for an ideal gas

From the first law, with $ Q=0$ , $ du = c_v dT$ , and $ \textrm{Work} = pdv$ ,

$\displaystyle du + pdv = 0.$ (2..7)

Also, using the definition of enthalpy,
$\displaystyle dh = \underline{du + pdv} + vdp.$ (2..8)

The underlined terms are zero for an adiabatic process. Rewriting (2.7) and (2.8),

$\displaystyle \gamma c_v dT = -\gamma pdv$

$\displaystyle c_p dT = vdp.$

Combining the above two equations we obtain
$\displaystyle -\gamma pdv = vdp\quad \textrm{ or }\quad -\gamma dv/v = dp/p.$ (2..9)

Equation (2.9) can be integrated between states 1 and 2 to give

$\displaystyle -\gamma ln(v_2/v_1) = ln(p_2/p_1)\textrm{, or, equivalently,}$

$\displaystyle (p_2 v_2^\gamma)/(p_1 v_1^\gamma)=1.$

For an ideal gas undergoing a reversible, adiabatic process, the relation between pressure and volume is thus:

$\displaystyle pv^\gamma = \textrm{constant, or}$

$\displaystyle p = \textrm{constant} \times \rho^\gamma.$

We can substitute for $ p$ or $ v$ in the above result using the ideal gas law, or carry out the derivation slightly differently, to also show that

$\displaystyle \frac{p_2}{p_1} = \left(\frac{T_2}{T_1}\right)^{\frac{\gamma}{\ga... ...uad \textrm{and} \quad \frac{T_2}{T_1} =\left(\frac{v_1}{v_2}\right)^{\gamma-1}$

We will use the above equations to relate pressure and temperature to one another for quasi-static adiabatic processes (for instance, this type of process is our idealization of what happens in compressors and turbines).





Practice Questions

  1. On a $ p$ -$ v$ diagram for a closed-system sketch the thermodynamic paths that the system would follow if expanding from $ \textrm{volume} = v_1$ to $ \textrm{volume} = v_2$ by isothermal and quasi-static, adiabatic processes.
  2. For which process is the most work done by the system?
  3. For which process is there heat exchange? Is it added or removed?
  4. Is the final state of the system the same after each process?
  5. Derive expressions for the work done by the system for each process.


Ucapan Terima Kasih:

Kepada Para Dosen di MIT dan Dosen Fisika FPMIPA Universitas Pendidikan Indonesia

Semoga Bermanfaat